Saturday, November 19, 2011

Complete wiper components replacing details for Acura Car Models?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The details are as follows :-----

This section contains:----
1) Intermittent Wiper Relay.
2) Windshield Washer Pump.
3) Windshield Wiper Blade and Arm.
4) Windshield Wiper Motor.

Intermittent Wiper Relay


The intermittent wiper function is controlled by either a specialized control unit or the integrated control unit. The integrated control unit controls other timed functions as well as the wipers.
The wipers are controlled by a relay located at the top left of the under dash fuse panel. On the Integra, the function is controlled by the integrated control unit located in the fuse and relay panel at the left kick panel.
The Legend uses a relay located in the center of the relay panel in the engine compartment. This relay is controlled by the integrated control unit located in the fuse and relay panel at the left kick panel. The Vigor is similar to the Legend, but the intermittent relay is located at the front of the engine compartment.

Windshield Washer Pump


REMOVAL & INSTALLATION



  1. Disconnect the negative battery cable.
  2. Locate and gain access to the water washer reservoir tank and pump.
  3. Detach the water motor electrical connector.
  4. Place a suitable drain pan under the vehicle. Drain the washer reservoir.
  5. Remove the washer reservoir from the vehicle.
  6. Remove the washer pump from the reservoir.
  7. Disconnect the washer hose from the pump.
To install:
  1. Connect the washer hose to the pump.
  2. Place the washer pump into the reservoir using a pair of pliers. Make sure the pump is pushed in all the way into the reservoir seal.
  3. Install the reservoir tank assembly.
  4. Attach the washer motor electrical connector.
  5. Refill the windshield washer reservoir.
  6. Connect the negative battery cable, then check for proper washer motor operation.

Windshield Wiper Blade and Arm


REMOVAL & INSTALLATION



  1. With the wipers on, turn the ignition OFF when the wiper is at the mid-wipe position. At the tip of the blade assembly, mark the windshield with a crayon to aid in reassembly.
  2. Lift the wiper arm assembly from the windshield and pull the retaining latch out.
  3. Lift the wiper arm assembly from the transaxle driveshaft.
  4. Disconnect the washer nozzle hose from the end of the wiper arm.
  5. If necessary, remove the blade as outlined in General Information and Maintenance of this guide.
To install:
  1. Connect the washer hose to the end of the wiper arm.
  2. Position the wiper arm assembly on the transaxle driveshaft.
  3. Push the retaining latch in to lock the wiper arm in position, then carefully lower the wiper arm and blade onto the windshield.


Windshield Wiper Motor


REMOVAL & INSTALLATION Front



See Figures 1 through 8
Click image to see an enlarged view
Fig. Fig. 1: Matchmark the wiper arm to the shaft. This will allow you to install the arm on the splined shaft in the correct position


Click image to see an enlarged view
Fig. Fig. 2: Once the arm is matchmarked, you can pull of off the shaft


Click image to see an enlarged view
Fig. Fig. 3: Use a small prytool to pop up the plastic fasteners


Click image to see an enlarged view
Fig. Fig. 4: After removing all of the retainers, pull the air scoop away from the windshield


Click image to see an enlarged view
Fig. Fig. 5: Loosen and remove the wiper motor linkage mounting bolts ...


Click image to see an enlarged view
Fig. Fig. 6: ... then remove the wiper motor and linkage assembly from the vehicle


Click image to see an enlarged view
Fig. Fig. 7: Unfasten the wiper motor mounting nuts ...


Click image to see an enlarged view
Fig. Fig. 8: ... then remove the wiper motor from the linkage assembly
  1. Disconnect the negative battery cable.
  2. Remove the cap nuts and wiper arms.
  3. Remove the hood seal.
  4. Remove the air scoop by prying it out of the trim clips.
  5. Remove the connector from the wiper molding.
  6. Remove the mounting bolts.
  7. Disconnect and remove the wiper linkage assembly.
  8. Remove the wiring harness from the linkage assembly.
  9. Separate the wiper linkage and the crank arm at the joint.
  10. Unfasten the three mounting bolts that hold the wiper motor to the mount, then remove the wiper motor.
  11. Installation is the reverse of the removal procedure.
Rear
  1. Disconnect the negative battery cable.
  2. Remove the cover, mounting nut, and wiper.
  3. Remove the rubber seal.
  4. Unfasten the special nut and remove the washer.
  5. Remove any trim panels that hinder removal.
  6. Detach the wiring connector from the wiper motor.
  7. Remove the motor mounting bolts, then remove the motor assembly.
  8. Installation is the reverse of the removal procedure.

-------------------
This details will help.
Thanks.

----------
For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------

No comments:

Post a Comment