Monday, November 14, 2011

How to remove Brake Disc Rotor on Acura Integra?

The procedure is as follows.Read it before performing this task.


Brake Disc (Rotor)


REMOVAL & INSTALLATION



See Figures 1, 2 and 3
Click image to see an enlarged view
Fig. Fig. 1: The use of a hand impact driver may be necessary to remove the brake rotor retaining screws


Click image to see an enlarged view
Fig. Fig. 2: Close up of the brake rotor retaining screws


Click image to see an enlarged view
Fig. Fig. 3: Remove the brake rotor by pulling it over the studs

CAUTION
Older brake pads or shoes may contain asbestos, which has been determined to be cancer causing agent. Never clean the brake surface with compressed air! Avoid inhaling any dust from any brake surface! When cleaning brake surfaces, use a commercially available brake cleaning fluid.

  1. Use a siphon or clean turkey baster to remove about half of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle and remove the tire/wheel assembly.
  3. Remove the caliper guide pin or mounting bolts.
  4. Lift the caliper assembly away from the brake rotor.
  5. Use a suitable piece of wire to suspend the caliper assembly from the upper control arm. This will prevent the weight of the caliper from being supported by the brake flex hose which will damage the hose.
  6. If equipped, remove the rotor retaining screws.
  7. Remove the brake rotor by pulling it straight off the wheel mounting studs.
To install:
  1. If installing the rotor on the rear brakes, use a commercially available locknut wrench, or equivalent tool, to turn the caliper piston clockwise into position in the cylinder, then align the cutout in the piston with the tab on the inner pad by turning the piston back.
  2. If installed the rotor on the front brakes, completely retract the piston into the caliper using a large C-clamp or other suitable tool.
  3. Install the brake rotor onto the wheel hub.
  4. Install the caliper assembly over the brake rotor and install the guide pin or mounting bolts.
  5. Fill the master cylinder to the proper level with fresh brake fluid.
  6. Install the tire/wheel assembly and lower the vehicle.
  7. Pump the brake pedal until the brake pads are seated and a firm pedal is achieved before attempting to move the vehicle.

CAUTION
Do not move the vehicle until a firm pedal is obtained.

  1. Road test the vehicle to check for proper brake operation.
InspectionSee Figure 4
Click image to see an enlarged view
Fig. Fig. 4: Use a micrometer to measure the thickness of the brake rotor. You must discard the rotor if it is not within the manufacturer's specifications
Whenever the brake calipers or pads are removed, inspect the rotors for defects. The brake rotor is an extremely important component of the brake system. Cracks, large scratches or warpage can adversely affect the braking system, at times to the point of becoming very dangerous.
Light scoring is acceptable. Heavy scoring or warping will necessitate refinishing or replacement of the disc. The brake disc must be replaced if cracks or burned marks are evident.
If the rotor needs to be replaced with a new part, the protective coating on the braking surface of the rotor must be removed with an appropriate solvent before installing the rotor to the vehicle.
Check the run-out of the hub (disc removed). It should not be more than 0.002 inch (0.050mm). If so, the hub should be replaced.
All brake discs or rotors have markings for MINIMUM allowable thickness cast on an unmachined surface or an alternate surface. Always use this specification as theminimum allowable thickness or refinishing limit. Refer to a local auto parts store or machine shop, if necessary, where rotors are resurfaced.
If the rotor needs to be replaced with a new part, the protective coating on the braking surface of the rotor must be removed with an appropriate solvent before installing the rotor to the vehicle.

-------------
------------
For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

Lexus: Anti-lock Brake System Actuator?


2001 Lexus IS 250 and IS 350.
Lexus: Actuator replacing for Anti-lock Brake System?
Click the link below:---



2001 Lexus ES 300 :---
How to replace ABS Actuator on 2001 Lexus?
Click the link below:---

Lexus: How to bleed ABS system?

Click the link below:--


What is ABS and how does it works on vehicles?


How to test ABS system in vehicle?


Lexus: Wheel Speed Sensors Removal?


How to manually bleed brake systems on Lexus?


How to remove brake pads on 2001 Lexus?


How to replace brake Caliper on 2001 Lexus ?


 

2001 Lexus: Brake Disc Rotor removal?


Brake Pads replacing on 2001 Lexus?


How to adjust parking Brake cable on 2001 Lexus?


How to adjust parking Brake shoes on 2001 Lexus?


Rear Brake Pads removal on 2001 Lexus?


Rear Brake Rotor replacing on 2001 Lexus?


Removing Rear Brake Caliper on 2001 Lexus?

http://howtobyme.blogspot.com/2011/10/removing-rear-brake-caliper-on-2001.html
-----------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------

No comments:

Post a Comment