Monday, November 14, 2011

How to remove Parking Brake Cable on Acura Integra?

The procedure is as follows :---


REMOVAL & INSTALLATION Except 3.5RL



See Figure 1
Click image to see an enlarged view
Fig. Fig. 1: Exploded view of a typical Acura parking brake cable and related components
  1. Disconnect the negative battery cable.
  2. Fully release the parking brake lever.
  3. Loosen the output cable adjuster nut from the parking brake cable tension equalizer. This will relieve tension from the parking brake cables allowing for easy removal.
  4. On Integra models, remove the lock and clevis pin.
See Figure 2
Click image to see an enlarged view
Fig. Fig. 2: Location of the holding clip, clevis pin, lever, and lock pin-all models except 2.5TL
  1. Installation is the reversal of the removal procedure.
3.5RL
  1. Disconnect the negative battery cable.
  2. Remove the parking brake switch connector.
  3. With the parking brake released, disconnect the parking brake cable from the pedal.
  4. Remove the parking brake pedal assembly from the vehicle by removing the mounting bolts.
  5. Remove the parking brake shoes.
  6. Remove the parking brake cable from the backing plate. Use a 12mm offset wrench as shown.
See Figures 3 and 4
Click image to see an enlarged view
Fig. Fig. 3: Use a 12mm offset wrench to remove the parking brake cable from the backing plate.


Click image to see an enlarged view
Fig. Fig. 4: Parking brake cable-3.5RL
To install:
  1. Install the parking brake cable into the backing plate.
  2. Install the parking brake shoes.
  3. Install the parking brake pedal assembly.
  4. Attach the parking brake cable to the pedal assembly.
  5. Install the parking brake switch connector.
  6. Connect the battery cable.
Adjustment Integra, CL, and TL Models
  1. Pull the parking brake with moderate force. This should position it six to ten notches up.
  2. To adjust the parking brake, begin by raising the vehicle.
  3. Properly support the vehicle.
  4. Check that the parking brake arm on the rear brake caliper is contacting the brake caliper pin.
  5. Pull the parking brake lever handle up one notch.
  6. Remove the rear console.
  7. Turn the adjusting nut until the wheels just begin to drag.
  8. Release the parking brake lever and check that the brakes do not drag when the wheels are spun.
  9. Install the rear console.
3.5RL and Vigor
  1. Raise and properly support the vehicle.
  2. Check to ensure that the lever of the rear brake caliper contacts the caliper pin.
  3. Advance the parking brake lever or pedal one notch.
  4. Lift up the console door.
  5. Remove the console bottom liner.
  6. Using a flexible extension and socket assembly turn the adjusting nut on the equalizer.
  7. Tighten until the wheels drag slightly when turned.
  8. Release the parking brake lever or pedal and check that the wheels do not drag excessively when turned.

WARNING
Overtightening the parking brake may cause the brakes to drag causing excessive heat build up and brake failure.

  1. If the parking brake is properly adjusted the rear brakes will be fully applied when the parking brake lever is pulled 7-11 notches for Vigor, or the pedal is depressed 6-8 clicks on the 3.5RL.
  2. Lower the vehicle.
Legend
The rear brakes should be engaged when a force of 44lbs. (200Nm) is applied to the parking brake lever. It should engage the brakes between eight to twelve notches.
  1. Remove the rear cover from the console.
  2. Pull the parking lever up one notch.
  3. Raise and safely support the vehicle.
  4. Tighten until the wheels drag slightly when turned.
  5. Release the parking brake lever and check that the wheels do not drag excessively when turned.

WARNING
Overtightening the parking brake may cause the brakes to drag causing excessive heat build up and brake failure.

  1. If the parking brake is properly adjusted the rear brakes will be fully applied when the parking brake lever is pulled eight to twelve notches.
  2. Install the rear console.
  3. Install the wheels.
  4. Lower the vehicle.

------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

Lexus: Anti-lock Brake System Actuator?


2001 Lexus IS 250 and IS 350.
Lexus: Actuator replacing for Anti-lock Brake System?
Click the link below:---



2001 Lexus ES 300 :---
How to replace ABS Actuator on 2001 Lexus?
Click the link below:---

Lexus: How to bleed ABS system?

Click the link below:--


What is ABS and how does it works on vehicles?


How to test ABS system in vehicle?


Lexus: Wheel Speed Sensors Removal?


How to manually bleed brake systems on Lexus?


How to remove brake pads on 2001 Lexus?


How to replace brake Caliper on 2001 Lexus ?


 

2001 Lexus: Brake Disc Rotor removal?


Brake Pads replacing on 2001 Lexus?


How to adjust parking Brake cable on 2001 Lexus?


How to adjust parking Brake shoes on 2001 Lexus?


Rear Brake Pads removal on 2001 Lexus?


Rear Brake Rotor replacing on 2001 Lexus?


Removing Rear Brake Caliper on 2001 Lexus?

http://howtobyme.blogspot.com/2011/10/removing-rear-brake-caliper-on-2001.html

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------


No comments:

Post a Comment