Friday, November 18, 2011

How to replace Power Steering Pump on Acura Car Models?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The procedure is as follows :----

Power Steering Pump


REMOVAL & INSTALLATION



  1. Place a suitable drain pan under the vehicle, then disconnect the power steering hoses from the pump to drain the fluid.
  2. Remove the belt by loosening the pump adjusting bolts and mounting bolts.
  3. On the 3.5RL, Legend or Vigor, remove the air cleaner cover and air intake duct.
  4. Cover the alternator (Integra, 2.2CL 2.3CL) or the crankshaft pulley (3.0CL 3.2TL) with some rags to protect it from any spilled power steering fluid.
  5. Disconnect and plug the inlet and outlet hoses from the pump.
See Figures 1, 2, 3 and 4
Click image to see an enlarged view
Fig. Fig. 1: Power steering pump mounting-Integra shown


Click image to see an enlarged view
Fig. Fig. 2: Power steering pump mounting-2.2CL and 2.3CL


Click image to see an enlarged view
Fig. Fig. 3: Exploded view of the power steering pump-3.0CL


Click image to see an enlarged view
Fig. Fig. 4: Steering pump-to-engine attachment-Vigor shown
  1. Unfasten the pump mounting bolt(s), then remove the pump from the vehicle.

WARNING
Do not turn the steering wheel with the pump removed.

  1. Cover the opening of the pump with a piece of tape to prevent any foreign material from entering the pump.
  2. If you are replacing the pump and need to transfer the pulley, hold the steering pump in a suitable soft-jawed vise, hold the pulley with a suitable universal pulley holding tool, then remove the pulley nut and pulley/
  3. Installation is the reverse of the removal procedure. Bleed the power steering system.

SYSTEM BLEEDING




WARNING
Use only genuine Honda power steering fluid. Any other type or brand of fluid will damage the power steering pump.

  1. Lift the power steering reservoir off of its mount. Disconnect the return hose from the steering rack at the reservoir. Immediately plug the reservoir inlet to prevent fluid loss and contamination. Don't disconnect the hose that connects the pump to the reservoir.
  2. Insert a length of rubber tubing into the return hose and route the tubing into a drain container.
  3. With the engine running at idle, turn the steering wheel lock-to-lock several times until fluid stops running out of the hose. Immediately shut the engineOFF .
See Figure 5
Click image to see an enlarged view
Fig. Fig. 5: Bleeding the air from the power steering system
  1. After servicing, reconnect the reservoir return line. Fill the reservoir to the upper line with genuine Honda power steering fluid.
  2. Run the engine at idle and turn the steering wheel lock-to-lock several times to bleed air from the system and fill the rack valve body.
  3. Recheck the fluid level and add more if necessary. Don't overfill the reservoir.
  4. Check the power steering system for leaks.
  5. Lower the vehicle.
See Figure 6
Click image to see an enlarged view
Fig. Fig. 6: Torque Specifications


---------------

This details will help.
Thanks.
----------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------


No comments:

Post a Comment